+- TheZombieGame.com Forums (http://www.thezombiegame.com/forums)
+-- Forum: Last Night on Earth (/Forum-Last-Night-on-Earth)
+--- Forum: LNoE Variants (/Forum-LNoE-Variants)
+--- Thread: Card Creation- Think its there!! (/Thread-Card-Creation-Think-its-there)
Pages: 1 2
Card Creation- Think its there!! - friskers96 - 03-28-2013 06:24 AM
So while messing about creating gimmick cards of the family to get a good system going for when I start pumping out my scenarios and stuff, I think I got it!! I used the hero template from the DL section that gives you the front and back on one sheet as well as the stand alone front side one (easier to manipulate the text with that one). Created my card and copied the layer over onto the sheet with both front and back. Important note, I had to raise the DPI to 300 from 79 to get a good image after printing. Got everything set and saved as a PDF, JPEG looked a little funny believe it or not. Went to Kinko's and had them print it out on a gloss cover stock. Got home and cut em out then mounted with spray adhesive to some chipboard I got from a scrap-booking store in the same plaza. Here are the results. Now that I got a good idea on paper, I can try and print from home, only issue is my printer is an ink hog, almost cheaper to print from kinko's.
RE: Card Creation- Think its there!! - samuraitrev - 03-28-2013 02:44 PM
Thet look amazing, great skills on recreating high quality looking character boards.
Re: Card Creation- Think its there!! - zachmaio - 03-28-2013 02:58 PM
Wow if the edges were rounded I wouldn't have been able to tell the difference between the two! Bravo!
RE: Card Creation- Think its there!! - friskers96 - 03-28-2013 10:55 PM
Thanks guys, I might have to possibly sacrifice a card to pull off the rounded corners. I might try with my die zombie die card to make a template I can't wait to make some L boards, I need to get better at photoshop so I can make some nice stuff from scratch..
RE: Card Creation- Think its there!! - fitzgrimm - 03-28-2013 11:15 PM
Friskers that is awesome. Just so you know if you go to a craft store they usually have a tool that well cut round corners. I think we paid about $8 for the one that we got for my wife. They are usually in the scrap book section and they work like a hole punch, you just put the tool on the corner of the page and press down. I well see if I can find a link so that you can see what one looks like.
Edit: This is not the exact one we have but similar.
RE: Card Creation- Think its there!! - friskers96 - 03-29-2013 05:56 AM
That is nice, ill defiantly check that out. I wonder if it will work on that chipboard too, it's pretty thick.
RE: Card Creation- Think its there!! - fitzgrimm - 03-30-2013 12:02 AM
Never tried it on chipboard but it works on heavy cardboard.
RE: Card Creation- Think its there!! - aldrichgreg - 04-01-2013 07:01 AM
(03-28-2013 10:55 PM)friskers96 Wrote: Thanks guys, I might have to possibly sacrifice a card to pull off the rounded corners. I might try with my die zombie die card to make a template I can't wait to make some L boards, I need to get better at photoshop so I can make some nice stuff from scratch..
you can probably trace a card to make a template that you can cut from if the tool that's previously mentioned won't cut through your material rather than risking cutting an actual card.
RE: Card Creation- Think its there!! - friskers96 - 04-01-2013 07:13 AM
I found one of the tools and it cuts cards fine just not the chip board... I'll give tracing a shot, I just have a hard time keeping the blade from wandering unless it has a guide.
RE: Card Creation- Think its there!! - friskers96 - 04-10-2013 11:48 PM
I ordered a "chomper" from the scrapbook store. It does 1/4" radius and 1/2" radius cuts and it works on the chipboard! It will hopefully be in soon...